As Gigabit Ethernet continues to evolve toward higher density and lower power consumption, the Marvell Alaska 88E1545—with its combination of “four integrated ports + QSGMII single-differential-pair uplink + native EEE support”—has become a highly cost-effective PHY choice for enterprise switches, industrial gateways, and embedded network modules. Mingjiada Electronics currently has the 88E1545-A1-LKJ2C000 in stock, providing a stable supply channel for R&D selection and mass production procurement.
I. What Is the 88E1545: A Single Chip Solving Four Gigabit PHY Channels
The 88E1545 belongs to the Marvell Alaska Quad series and integrates four fully independent Gigabit Ethernet transceivers on a single chip. Each transceiver fully implements the physical layer functions of 1000BASE-T, 100BASE-TX, and 10BASE-T, supports full-duplex and half-duplex modes, and can operate on CAT 5 twisted-pair cable (1000BASE-T/100BASE-TX) as well as CAT 3/4/5 cable (10BASE-T).
Its core value lies in the aggregation design at the system interface: QSGMII consolidates traffic that would otherwise require four SGMII links onto a single pair of 5 Gbps differential signals, equivalent to serializing four 1.25 Gbps SGMII channels into a single high-speed link. For switch chips, this significantly reduces the number of I/O pins on the MAC interface, thereby lowering the number of PCB routing layers and connector resources required, while also improving overall power consumption.
II. Key Features: Why the 88E1545 Is Suitable for High-Density Gigabit Designs
① QSGMII Interface: Four Ports Require Only a Single Differential Pair
While implementing four Gigabit PHYs within a 128-pin LQFP package, QSGMII simplifies MAC-side interconnects to a single differential pair, directly reducing pin count constraints for switch chip selection and the complexity of multilayer PCB routing.
② Energy-Efficient Ethernet (EEE) and Low Per-Port Power Consumption
The chip is fully compatible with the IEEE 802.3az Energy-Efficient Ethernet standard and features built-in EEE buffering—even if the remote MAC device does not support EEE, the 88E1545 can still achieve a certain degree of energy savings on the link side. In copper cable applications, power consumption per port is approximately 400 mW; when all four ports are fully loaded, the total power consumption of the PHY section is kept at around 1.6 W, making it particularly well-suited for thermal design in fanless or enclosed devices.
③ Integrated Switching Regulator, Single 3.3 V Power Supply
The chip integrates a switching voltage regulator that generates the voltages required for the core and I/O from a single 3.3 V power supply, eliminating the need for multiple external LDOs or DC-DC converters and significantly simplifying the power tree.
④ Virtual Cable Tester (VCT) and Auto-MDIX
The integrated VCT function detects and reports cable faults such as open circuits and short circuits, with positioning accuracy within one meter, providing physical-layer observability for field deployment and post-sales diagnostics. Auto-MDIX automatically identifies straight-through or crossover wiring configurations at all three speeds (10/100/1000M), reducing cabling constraints during installation.
⑤ Compact Packaging and Key Specifications
The device features a 128-pin LQFP (14 mm × 20 mm, with exposed pads) green package, where the exposed pads also facilitate heat dissipation. Key specifications at a glance:
Number of Ports: 4 independent Gigabit ports
Data Rates: 10 Mbps / 100 Mbps / 1 Gbps
MAC Interface: QSGMII
Ethernet Standards: 1000BASE-T / 100BASE-TX / 10BASE-T
Supply Voltage: 1.71–1.89 V / 2.38–2.63 V / 3.13–3.47 V (integrated switching regulator)
Package: 128-LQFP-EP (14×20 mm)
Operating Temperature: 0°C to 70°C (commercial grade)
Protocol Compliance: IEEE 802.3 / IEEE 1149.1 (JTAG)
III. Typical Application Scenarios
With its four-port integration, QSGMII interface, and energy-efficient features, the 88E1545 is suitable for the following scenarios:
Enterprise Networking Equipment: Multi-port Gigabit switches and routers, providing high-density connectivity for office networks.
Industrial Automation and Embedded Systems: Industrial gateways, embedded motherboards, and network modules; the low power consumption and compact package are well-suited for harsh space and thermal conditions.
Storage and Consumer Networking Equipment: NAS, multi-port network-attached devices, and other scenarios requiring multiple Gigabit physical layer interfaces.
IV. Mingjiada Electronics: 88E1545 in Stock
Mingjiada Electronics has long specialized in the distribution of genuine electronic components from brands such as Marvell, maintaining stable inventory depth and supply capabilities for the 88Q/88E/88NV series. Key information for the currently available 88E1545-A1-LKJ2C000 is as follows:
Part Number: 88E1545-A1-LKJ2C000
Brand: Marvell
Package: LQFP-128
Stock Quantity: 2,000 pieces (in stock)
Lead Time: Brand-new, genuine; immediate confirmation upon inquiry
For teams currently developing multi-port Gigabit switches, industrial gateways, or embedded network modules, the 88E1545 remains a top candidate for evaluation among four-port Gigabit PHY options due to its combined advantages in three key areas: QSGMII pin compatibility, 400 mW per-port power consumption, and a single 3.3 V power supply. Mingjiada Electronics’ in-stock inventory provides reliable supply assurance for the transition from prototype verification to small-batch trial production.
Quotation and Selection Support: Visit the product page on the Mingjiada Electronics website (www.hkmjd.com) to view real-time inventory and pricing for the 88E1545-A1-LKJ2C000, or contact the sales team to confirm batch availability and delivery times.
Tags: 88E1545-A1-LKJ2C000, 88E1545-A1-LKJ2C00, 88E1545-A1-LKJ2C0, 88E1545-A1-LKJ2C, 88E1545-A1-LKJ2, 88E1545-A1-LKJ, 88E1545-A1-LK, 88E1545-A1-L, 88E1545-A1, 88E1545-A, 88E1545
Persona de Contacto: Mr. Sales Manager
Teléfono: 86-13410018555
Fax: 86-0755-83957753